|
|
MASTERCRAFT
|
OTHER
|
|
Frame
|
.065, ¾” mild steel. Head rest applied separately - won't affect the integrity of the frame
|
.049, ¾” mild steel. Back frame is all one piece - can't change the angle of headrest
|
|
Mounting
|
Tubing runs along floor and back up to itself, with flat strap running from front to back, allowing weight to be evenly disbursed throughout the bottom of the seat - No tweaking
|
4 -1 ½”-wide tabs welded on corners
|
|
2nd Suspension
|
(2) Pirelli rubber straps added for extra support in the tailbone area
|
Straps not used
|
|
Suspension Liner
|
Mesh - no seams in sling - all one piece
|
Coated vinyl - 2-piece sling sewn together at bottom of seat/back and headrest seam
|
|
Sling attachment
|
Flaps have 1-in. extruded plastic strips sewn in. Brass grommets provide a stable non-moving anchor for flaps to join with lacing cord. Cord is used only to attach flaps together. Provides continuous balance
|
.090 hanger wire provides an unstable moving area for flaps to join together. Lacing cord is used as a major part of the suspension. Provides inconsistent balance
|
|
Side Flaps
|
Face each other with a maximum spread of 2 inches
|
Face each other with a spread of 4-½ inches - more cord
|
|
Bottom Flaps
|
Face each other with a maximum spread of 2 inches.
|
Face each other with 15-inch spread.
|
Headrest Cap
Back Flap
|
Separate piece, seamed at top with foam added for comfort. Sling wraps around ¾" tubing in shoulder area with an 18-inch spread
|
Sling runs up to top of headrest and is seamed at top with foam added. Seam at headrest supports entire back suspension. No attachment to back of frame
|
|
Stitching
|
.055 length of stitch - more stitches per inch
|
.090 length of stitch - less stitches per inch
|
|
Lacing cord
|
Used to hold the suspension flaps together
|
Used as a major part of the bottom suspension
|
|
Foam
|
All foam is 1.4 lb. - Heavier density & fire retardant. Foam is cut in various sizes. Placed around all edges to protect cover and give added comfort
|
All foam is1.0 lb. - Lighter density & fire retardant. Foam cut in various sizes. Placed around all edges to protect cover and give added comfort
|
|
Inside back
|
1.4 lb (heavier) foam in lumbar area is 3 inches thick
|
1.0 lb. (lighter) foam in lumbar area is 2 inches thick
|
|
Inside base
|
1.4 lb. (heavier) foam 2-4 inches in bottom of seat
|
1.0 (lighter) foam 1-2 inches in bottom of seat
|
|
Inside sides
|
1.4 lb. (heavier) foam is 1-inch thick
|
1.0 lb. (lighter) foam is 1-inch thick
|
|
Slot covers
|
Vinyl is placed over the 5-point slots - you don't see the foam
|
Not covered
|
|
Cover
|
Nylon fabric glued to ½” muslin-backed foam. All seams are double stitched at start and finish – no friction between fabric/foam for longer wear
|
Nylon fabric joined to 1-inch foam with single-lined seam, no back stitching. Causes friction/puckering in cover
|
|
Back
|
(3) separate pieces of vinyl sewn together to create a polished look
|
(1) piece of vinyl, no additional sewing
|
|
Belt holes
|
Reinforced with liner material for extra strength
|
Not reinforced
|
|
Band
|
Vinyl glued to ½” foam for additional padding, sectioned for custom fit to follow contours of seat
|
Vinyl one-piece band, no foam added
|
|
Welt
|
Vinyl hand-wrapped around welting
|
Vinyl hand-wrapped around welting
|
|
MOST IMPORTANTLY
|
You will find our name on every product we make!
|
No identifying tag or name
|
